显示标签为“refractory”的博文。显示所有博文
显示标签为“refractory”的博文。显示所有博文

2017年10月23日星期一

Refractory for heating furnace

Refractory for heating furnace
Refractory for heating furnace
With the large-scale and high efficiency of the rolling mill, the heating furnace put forward higher demand, its development trend is large, low consumption, pollution-free and operational automation, building materials and therefore divided into side-open and lift Two kinds. The door is generally made of clay brick, refractory castable or refractory plastic, high aluminum insulation brick or refractory fiber mats and other materials for lining. Side open the door can use a furnace service, lift door due to temperature fluctuations and mechanical impact and other factors, the service life of about la. Out of the riveting with refractory material with the side of the billet heating furnace.
In addition to water-cooled cast iron out of the trough, the general use of high alumina brick or masonry masonry, the service life of 3 to 6 months. Sintered mullite or fused mullite large brick masonry, high strength, good wear resistance, but the thermal shock resistance is poor, easy to crack, its life around 1a. The use of heat-resistant steel fiber staggered corundum refractory castable in the field into the overall steel trough, the service life of more than 2a.
Ceramic chute with a small push-type refractory furnace, from the corundum a silicon carbide slide rails composed of ceramic slide. In the length of the furnace with a refractory brick masonry two or four rows of the wall. In the base wall masonry high alumina silicon carbide brick, and then install the sliding rail brick and composed of ceramic slide. Billet in the slide on the move to achieve the upper and lower sides of the heating, with less energy, billet without black and so on. Ceramic chute to withstand high temperature, billet load, high temperature wear and corrosion of iron oxide slag and other effects, the use of more demanding conditions, the life of about 1a. The bottom of the water cooling 'adiabatic refractory materials, large and medium-sized push silver or walking beam furnace, the bottom of the water cooling pipe is a vertical, horizontal distribution and support the role of thick-walled water cooling pipe composition. The purpose of adiabatic is to reduce the heat from the cooling medium, reduce the billet black print and improve the quality of heating.
The adiabatic way is divided into special-shaped clay brick mosaic or horseshoe-shaped brick hanging, refractory plastic or refractory castable made of welded tile prefabricated block welding or with the material and refractory fiber felt on-site dressing. Life is generally 3 to 12 months. When the use of high-quality refractory plastic, ultra-low cement or cement-free refractory castables for field dressing, the life of more than la. Flue and smoke for their own use refractory lase lining generally with dry clay masonry, can also be used refractory castable prefabricated block hanging or on-site watering, and sometimes can be used refractory spray coating construction. Red brick or concrete chimney in high temperature area with refractory masonry. Metal chimney wall welding metal anchor nails, sometimes with metal mesh, the use of lightweight refractory castable or refractory spray for lining, construction convenience, integrity, long service life. (Refresable for rehea-ting fumace) Refractory materials used in masonry furnaces and related parts. The furnace is used for rolling or forging steel. Heating billet or small steel ingot thermal equipment, the use of the temperature is generally 13 of a 1 40. ℃.
This type of furnace is generally made of refractory clay brick masonry, heating section and soaking section roof is also useful 3-high aluminum brick 'lining damage is mainly due to high temperature, thermal stress, air erosion and mechanical collision caused by the role of high temperature The lower part of the furnace wall, the bottom of the furnace and the water-cooled tube packing layer and other parts are also affected by the erosion of molten iron oxide slag, therefore, masonry or mattress magnets for the protective layer, water pipe dressing layer with high alumina refractory. With the large-scale rolling mill and high efficiency, the heating protection made a higher demand, its development trend is large, low consumption, pollution-free and operational automation, building materials and therefore open and lift two The The door is generally made of clay brick, refractory castable or refractory plastic, high aluminum insulation brick or refractory fiber mats and other materials for lining.
Side open the door can use a furnace service, lift door due to temperature fluctuations and mechanical impact and other factors, the service life of about la. Out of the riveting with refractory material with the side of the billet heating furnace. In addition to water-cooled cast iron out of the trough, the general use of high alumina brick or masonry masonry, the service life of 3 to 6 months. The use of sintered or fused mullite large brick masonry, high strength, good wear resistance, but the thermal shock resistance is poor, easy to crack, its life around 1a. The use of heat-resistant steel fiber staggered corundum refractory castable in the field into the overall steel trough, the service life of more than 2a. Ceramic chute with a small push-type refractory furnace, from the corundum a silicon carbide slide rails composed of ceramic slide. In the length of the furnace with a refractory brick masonry two or four rows of the wall.
In the base wall masonry high alumina silicon carbide brick, and then install the sliding rail brick and composed of ceramic slide. Billet in the slide on the move to achieve the upper and lower sides of the heating, with less energy, billet without black and so on. Ceramic chute to withstand high temperature, billet load, high temperature wear and corrosion of iron oxide slag and other effects, the use of more demanding conditions, the life of about 1a. The bottom of the water cooling 'adiabatic refractory materials, large and medium-sized push silver or walking beam furnace, the bottom of the water cooling pipe is a vertical, horizontal distribution and support the role of thick-walled water cooling pipe composition. The purpose of adiabatic is to reduce the heat from the cooling medium, reduce the billet black print and improve the quality of heating. The adiabatic way is divided into special-shaped clay brick mosaic or horseshoe-shaped brick hanging, refractory plastic or refractory castable made of welded tile prefabricated block welding or with the material and refractory fiber felt on-site dressing. Life is generally 3 to 12 months. When the use of high-quality refractory plastic, ultra-low cement or cement-free refractory castables for field dressing, the life of more than la.
Flue and smoke for their own use refractory lase lining generally with dry clay masonry, can also be used refractory castable prefabricated block hanging or on-site watering, and sometimes can be used refractory spray coating construction. Red brick or concrete chimney in high temperature area with refractory masonry. Metal chimney wall welding metal anchor nails, sometimes with metal mesh, the use of lightweight refractory castable or refractory spray for lining, construction convenience, integrity, long service life. Refractory material for refineries for rehea-ting fumace The refractory used in masonry furnaces and related parts The heating furnace is a thermal equipment used to heat billets or small billets when rolled or forged steel. Generally for a 13 of 13. ℃. This type of furnace is generally made of refractory clay brick masonry, heating section and soaking section roof is also useful 3 high aluminum refractory bricks' lining damage is mainly due to high temperature, thermal stress, air erosion and mechanical impact caused by such a high temperature The lower part of the furnace wall, the bottom of the furnace and the water-cooled tube packing layer and other parts are also affected by the erosion of molten iron oxide slag, therefore, masonry or paving magnesia for the protective layer, water pipe dressing layer with high alumina refractory.


More refractory material:
http://www.yilongrefractory.com/AllProductServlet?id=1&number=20
E-mail:sales8@chinaelong.com

2016年12月15日星期四

Ladle Permeable Well Block---Refractory Brick---Refractory Material---Changxing Refractory

Ladle Permeable Well Block

Introduction:
Made from high-purity, high-density, high-strength materials and MAS matrix-optimized system, shaped by pressing, prefabrication and vibration. With subtle formula design, unique technical process, they have, which identified up to the leading domestic level and received recognition and praise.

Advantages:
1. Good corrosion/erosion resistance 2. High temperature performance 3. Longer service life 4. Stable structure 5. Thermal shock resistance

Application:
They suit specially for large-sized refining ladles

Content source:
http://www.yilongrefractory.com/AllProductOneServlet?id1=1&id=8
E-mail:sales8@chinaelong.com

2016年10月24日星期一

High temperature refractory insulation material for kiln - ceramic fiber cotton

Product manual:

The basic characteristics of the ceramic fiber loose cotton are the stable performance, light weight, low heat capacity, good thermal shock resistance, erosion resistance and sound absorption performance under the high temperature condition. Modern high-tech light-resistant materials can make suitable for special requirements, full Foot customer needs. Ceramic fiber cotton Silicate fiber cotton with stable performance, fiber length, tensile strength, large slag ball, high thermal stability, color,white and so on. Classification temperature 1050-1600 ℃. Is the production of fiber textile materials of choice, but also high temperature environment Sealing, filling and insulation of the ideal refractory material.

Product Features:

Low thermal conductivity, thermal shock resistance, high flexibility, good sound-absorbing properties, without any binder and other corrosive substances, high temperature is still loose and flexible and has good flexibility Anti-corrosion, excellent sound absorption, excellent Thermal stability.

Typical application:

Industrial ceramic fiber wet raw materials; ceramic fiber unshaped products of raw materials; high-temperature furnace, heating device, wall lining gap filler and so on.

First, as the base material, can be used as plate, paper, vacuum forming parts and other fiber deep processing of raw materials

Second, the expansion joints or short-term insulation repair filler material

Third, thermal insulation concrete and composite reinforcement

Four; high-temperature furnace, heating devices, wall lining gap filler with ceramic fiber cotton
Note: Because of its high performance characteristics, will be a revolutionary solution to a variety of technical problems, its application areas for metallurgy, ceramics, electronics, building materials, automotive, aerospace, glass and so on.

Refractory company Henan Xinmi Changxing Refractory Material Co., Ltd. Located in Henan Province,China.ChangXing's product portfolio covers shaped products such as refractory materials,refractory brick for sale, refractory castable,refractory nozzle, ceramic fiber, slide gate, etc; unshaped products including repair, construction and casting mixes and mortars.exported to more than 20 countries, such as Thailand, Indonesia, Pakistan, Saudi Arabia, South Africa, Turkey, Iran, Iraq and so on.

2016年10月10日星期一

Iron and steel enterprises on the energy-saving emission reduction refractory material high demand

With the development of iron and steel industry, iron and steel enterprises are also increasing the requirements of refractory company: the requirements of a longer service life and cleaner liquid steel.

In recent years, some domestic refractories suppliers to take refractory contracting system, the refractory supply, construction and maintenance to the contractor responsible for the price per tonne of steel to settle. This can mobilize the enthusiasm of refractory suppliers, to reduce consumption and its economic benefits linked to, but also effectively improve the user's economic environment, will help accelerate the reduction of China's metallurgical refractories consumption. To complete the consumption from the previous more the more the more profitable consumption to the less profitable transformation of the contracting model is not only a change in management mode, more importantly, technical upgrading, especially the application of technology to enhance the use of refractory The material is adapted to the operating conditions as far as possible. The use of refractory brick for sale technology in China is relatively backward, at the same time, the lack of refractory material suppliers use experience.

Recently, an iron and steel enterprises through a series of measures to make it 60 tons of LF ladle service life from the original 40 times to 50 times extended to 88 times, refractory unit consumption from 9.3 kg per ton steel down 5.6 kg per tonne, with remarkable results . We summarize their experience as follows. The EAF tapping temperature is generally 1620 ℃ ~ 1650 ℃. Normal ladle temperature of 1590 ℃ ~ 1620 ℃, ladle capacity of about 59 tons. Ladle refining time of 40 minutes to 50 minutes, a total of about 110 minutes of steel time. Argon pressure 0.2 MPa ~ 0.4 MPa, LF refining ratio of 100%, generally each furnace plus deoxidizer SiC 40 kg to 50 kg. The chemical composition of the ladle slag is: Fe2O31.44%, Al2O35.6%, CaO40.42%, CaF29%, MgO9.97%, SiO229.84%. This indicates that the ladle slag is a low basicity slag containing fluorite. The amount of slag in the electric furnace is large, and the oxidization of the slag is strong at the end of the electric furnace, and the content of FeO is always 45%.

Before the improvement, the iron and steel enterprises 60 tons of LF ladle slag line was used MT-14A magnesium carbon brick, pool with AMC brick. It is possible to use the physical and chemical properties of such bricks. In particular, the slag line, the use of magnesia carbon brick has a good density. The use of slag magnesia carbon brick is: the first slag line brick to use 15 to 19 times, the slag has been eroded to 50 mm below. In this case, the ladle will be off the assembly line, replace the ladle slag line brick. The second slag line of magnesium carbon brick service life of only about 15 times, and then again replace the third slag line of magnesium carbon brick, its service life can only reach 12 to 14 times, the total life of three slag only 40 times ~ 50 times, or even only to about 40 furnace times. The researchers observed the surface morphology of the ladle after use, found that the brick erosion uniformity, no increase in the phenomenon of brick, bricks did not appear like buns, guns, peeling and fracture anomalies, slag erosion rate of 7 mm ~ 10 mm, wall erosion rate also reached each 2.5 mm ~ 3.5 mm. Therefore, the main reason for the service life of the ladle is the rapid erosion of the slag line.
The main reason for this ladle erosion is that the basicity of slag is low, the lower the ratio of CaO and SiO2 is, the more the slag dissolves MgO, that is, the stronger the dissolving ability of slag to MgO. The low basicity slag on the corrosion of magnesium carbon brick is more serious. According to the analysis, they have taken the method of increasing the content of CaO in the brick so as to increase the ratio of CaO and SiO2 in the system after contact with slag and improve the melting point and viscosity of the system after slag reaction, so as to reduce the erosion speed. .
Because the amount of slag during the electric furnace tapping large, and the final oxidation of the furnace slag strong, which led to the early ladle slag has a high FeO content, resulting in magnesium carbon brick in the carbon easily oxidized, thus speeding up the slag line magnesium carbon Brick damage rate. According to this situation, the oxidation resistance of slag MgO-C brick needs more attention. After the modified slag MgO-C bricks at 1000 ℃ after 3 hours of oxidation resistance test, the oxidation decarburization layer is only 1 mm, while the improved MT-14A slag MgO-C brick oxidized decarburization layer thickness of 5 mm to 7 mm . Therefore, the modified slag MgO-C brick has good oxidation resistance.

In the steelmaking process, 50 to 60 kg of fluorite is added to each steel, which reduces the slag viscosity because the depth of penetration of the slag is inversely proportional to the square root of the viscosity. At the same time, it also accelerated the slag penetration of refractory materials, and lead to the slag line of magnesia carbon brick oxidation and erosion significantly improved. Therefore, the design of the production of magnesium carbon bricks, should be selected to improve the viscosity of fluorite-containing slag additives, which is conducive to improving the anti-slag erosion, but also conducive to extend the life of ladle.

As the common technology of MgO-C brick, it can improve the density of the product, the crystallinity and the purity of the raw material can significantly improve the corrosion resistance of MgO-C brick. For increased performance, large crystalline high purity fused magnesia, high purity natural graphite, and appropriate antioxidants and enhancers should be used. However, taking into account the economic efficiency of enterprises in the selection of materials should pay special attention to price. The enterprise to meet the basic requirements of the life of the case, the use of a certain amount of post-use magnesium-carbon brick renewable materials, and the use of some low-cost MP binding agent. For the regeneration of magnesium carbon materials, fewer fake particles and impurities, the more can improve the use of recycled magnesium carbon brick effect. Therefore, as far as possible the regeneration of magnesium carbon brick material removal, removal of fake particles, in order to improve the quality of recycled magnesium carbon bricks. MP binder is an asphalt modified resin binder, its residual carbon has a certain graphitization structure, with high oxidation resistance, thermal bonding properties and thermal shock resistance. Therefore, the choice of both antioxidant and enhance the role of composite additives, will help improve the performance of magnesium-carbon brick.

Based on the principle of optimal cost performance, the enterprise adopts the high quality recycled magnesium carbon material as the main raw material, with the appropriate content of 97% MgO fused magnesia, a small amount of -195 grades of graphite, composite Additives and modified resin binder, the ingredients, in the 630 tons of friction press molding, after curing system in the regeneration of magnesium carbon brick. Recycled Mg-C brick has good physical and chemical indexes, which fully meets the requirements of the national MT-12A and MT-14A quality products.

The improved MgO-C brick was applied to 60 tons of LF ladle, showing excellent corrosion resistance, oxidation resistance and thermal shock resistance. Ladle slag life from the use of MT-14A before the improvement of the Mg-C brick 15 to 19 times increased to 24 to 28 times, the erosion rate from 7 mm to 10 mm each time to 4.5 mm to 6.8 mm; From 40 to 50 times to 45 to 55 times, the erosion rate from 2.5 mm to 3.5 mm each time to reduce to 1.2 mm to 2.4 mm each. The application of this product, reducing the maintenance of ladle, get a good user evaluation.

Slag leaving slag operation: Because the final slag FeO content, not only affect the raw material yield, increased steelmaking costs, but also led to the refinement of ladle lining shorten the service life. By adjusting the oxygen gun, the angle and depth of the carbon gun, and strengthen the latter part of the electric furnace carbon spray, improve the foam slag and other methods to reduce the slag FeO content and reduce the slag in the oxygen activity, so that slag separation to reduce the amount of slag. Practice has proved that by controlling the amount of slag and slag in the FeO content, the life of refined ladle extended from 50 to 60 times, the life of refined ladle extended by 20%.
Add slag modifier: steel with SiC deoxidizer, with the electric furnace slag and slag FeO content increased, according to the deoxidation reaction: SiC +4 FeO = 4Fe + SiO2 + CO2 need more SiC deoxidizer, not only lead to refining The cost of steel increases, and the ratio of CaO and SiO2 in ladle slag is reduced, which greatly accelerates the erosion of lining. In order to reduce the ladle slag erosion of the lining, deoxidizer without SiC quality, and carbon content of 15% of the calcium and magnesium carbon steel ladle modifier, the addition of silicon carbide deoxidizing agent is basically the same, that is, per ton of steel by adding 1 kilogram. CaO in the modifier improves the basicity of the ladle slag, so that the MgO carbon brick in the erosion of MgO weakened low, MgO in the modifier MgO can increase the concentration of slag, magnesium and carbon brick to reduce MgO Of the dissolution rate. Through the trial of Mg-Ca carbonaceous modifier, the one-time service life of slag line MgO-C brick was extended from 26 times to 30 times, 15% longer.

Improve the maintenance system: slag erosion fast, the beginning of the two slag line corresponds to a molten pool. Later, with the two high aluminum brick on the pool were subsidized, that is, with the thickness of 40 mm of the two high aluminum brick attached to the molten pool, paste between the brick and the original lining with plastic binder and packing. The service life of molten pool from 60 to 88, extended by more than 45%.

2016年10月8日星期六

Selection Method of Refractory Lining for Different Parts of Blast Furnace

In the production process, the refractory lining of the furnace wall by a variety of role and gradually be eroded, so the choice of the various parts of the refractory brick lining should follow the principle is: refractory lining lining with the part of the heat flow intensity corresponds to, To keep the brick under the impact of strong heat flow

Lining to maintain integrity and stability; refractory lining with the part of the erosion mechanism should be corresponding to ease and delay the lining damage rate, to extend the life of blast furnace; try to use the price / performance than the low refractory, the choice of price Relatively low performance and good resistance

Firebrick, should not blindly choose expensive high-grade refractories. Each part of the firebrick lining selection method is:
(1) furnace throat. Mainly into the charge of the impact and wear, the general selection of steel or water-cooled steel bricks.
(2) the upper part of the furnace. This area is prone to carbon deposition reaction area, and alkali metal, zinc vapor erosion is also occurring in the region, together with the decline in charge and rising gas flow erosion and wear, it should be used to resist chemical erosion and abrasion resistance Of the refractory material

Material, the most suitable high-density clay brick, high-density third-class high-alumina brick or phosphoric acid-impregnated clay brick. Modern large-scale blast furnace on the use of thin-walled structure, the commonly used 1 to 3-stage buckle instead of brick wall lining.
(3) in the lower body and furnace waist. The main mechanism of damage is thermal shock, high temperature gas scour, alkaline metal, zinc and carbon analysis, as well as the initial chemical erosion of slag. Brick lining should be used for thermal shock resistance, resistance to early slag erosion and erosion of refractory castable Now at home and abroad

Large blast furnace selection of good performance but expensive silicon carbide brick (silicon nitride combination, self-bonding, combination of SIAL), so that the life of more than 8 years. Practice has proved that even the best refractory used for Blast Furnace is to be eroded, to balance (probably erosion to the original thickness of half

) Can be stable, this time is about 3 years. In fact, the use of good performance of fired aluminum carbon brick (much cheaper), can achieve this goal. So 10003 and below the blast furnace can be used aluminum carbon brick.
(4) furnace belly. The main reason for the damage is the scouring of high temperature gas and the scouring of slag iron. The heat flux of this part is very strong. Any refractories can not be resisted for a long time, mainly in slag skin, so this part need not be selected.
Too expensive refractories. This part of refractory company life is not long (1-2 months is long, short is 2-3 weeks), the general selection of high refractoriness, load softening temperature and high bulk density refractories, such as high alumina brick, aluminum carbon brick Wait.
(5) hearth tuyere area. This site is the only area of ​​the blast furnace oxidation reaction, the resulting high temperature up to 1900 ~ 2400), brick lining by high temperature caused by the destruction of thermal stress, and high temperature gas scouring, slag erosion, alkali metal erosion, cyclic movement coke

Of the erosion and so on. Modern blast furnace are combined brick masonry tuyere area, made of high aluminum, corundum mullite, corundum and silicon nitride silicon carbide, etc., but also useful for hot-pressed carbon block.
(6) hearth bottom and bottom. Blast furnace lining erosion of serious areas, the degree of erosion has always been to determine the basis for the generation of blast furnace life. The early bottom of the furnace because no cooling, mostly using a single ceramic refractories, thermal stress so that masonry cracks, hot metal

Penetration into the seam leaving the furnace floor brick is the main reason for the damage. The use of good bottom structure (ceramic cups, staggered bite, etc.) and cooling, as well as the use of high quality corundum, gray corundum bricks and carbon microporous, hot pressed bricks, greatly prolongs the blast furnace bottom life. but

Is the molten iron on the carbon brick osmotic corrosion, chemical corrosion of alkali bricks on the carbon brick, thermal stress on the destruction of carbon brick, C02 and H20 on the oxidation of carbon brick is still a threat to the hearth, furnace life important factors, and iron The circulation of the molten iron at the time of the movement on the cylinder liner lining the circumference of the machinery

Scouring and erosion are the primary factors of hearth damage.
This part of the refractory using high thermal conductivity, high permeability, high chemical resistance, low porosity, small pore size hot-pressed small carbon bricks, microporous carbon brick, carbon brick and hot-pressed semi-graphite used in ceramics Cups of corundum or gray corundum bricks. In a very long period of time

Time, small and medium-sized blast furnace using electric calcination anthracite made of high quality self-baking carbon block also achieved very good results. But changed to ceramic cup structure, you should not use self-baking carbon block, and use a roasted carbon block. Because the ceramic cup structure on the high-alumina refractory insulation

Self-baking carbon brick loss of self-baking conditions, can not make self-baking carbon brick to form a whole, so there have been several production burnout accident (North Taiwan, etc.).
Tiekou District, poor working conditions, and now the furnace with refractories matched the combination of iron brick masonry, the production of carbon, semi-graphite, mullite and so on.

2016年9月23日星期五

Magnesia aluminum refractories is Basic Refractories

Ladle Magnesia Carbon Brick
Ladle Magnesia Carbon Brick are used in Ladle linings, ladle upper and lower slag line, ladle wall and ladle bottom
Magnesia aluminum refractories of Basic Refractories:
Ladle steel industry is an important and indispensable equipment, as ladle lining, several major changes. Used to be traditional by sintering of clay refractory brick and third class alumina brick, the refractory material shows poor chipping resistance and corrosion resistance during use, low life, an average of only 10 times, dried treatment can only reach about 20 times. With the development of steelmaking technology, refining the molten steel to improve the outer retaining ladle lining insulating castable requirements in the early years of the 20th century that is, once the application as a whole

Cast Mg-Al quality ladle lining material. This lining integrity, and significantly improve the service life, but there are baked ladle long time, there are more serious dregs phenomenon for medium and small mills no special equipment most circumstances, unpacking difficult. To compensate for this deficiency, then the successful application of aluminum-magnesia unfired brick. The lining brick building is easy to assemble, baking time is short and easy unpacking, but still easy to kill slag and chipping resistance is poor. On this basis, in order to overcome the problem of aluminum-magnesia unfired brick ladle lining easy cat slag around the corner late he has not developed the aluminum-magnesia carbon brick, replacing the aluminum-magnesia unfired brick. The material combines the properties of aluminum-magnesia material and carbonaceous material. The main advantages of aluminum-magnesia carbon brick does not have: no cracks between the blocks melt loss, has good resistance to thermal shock resistance and slag ability to overcome the structural steel and slag penetration flaking, significantly improved service life and so on. Because the article is not burning or low-temperature firing, save energy, reduce costs, economic efficiency is very obvious, it attracted people's attention.


China advised in the 20th century, it began with bauxite and magnesite (or light burned MgO) magnesia aluminate spinel raw materials research. In recent years, also carried out a series of studies preparation of magnesia spinel products combine technology, achieved a lot, but the performance has been excellent in high purity products suffer from a high degree of firing is very limited. Domestic activity spinel powder was used. The ultra-high temperature firing process overseas (1 850c) down to 1 660C. But for the average coal-fired furnace refractory general terms, it is still difficult to achieve. To this end, the domestic refractory experts and scholars made active magnesia aluminum gum as a binding agent, was studied with the active Mg-Al gum as binding agent and high-purity magnesia carbon brick magnesia brick spinel combination of performance, the use of magnesia aluminum adhesive activity, both make excellent performance products fired at 1 550 ℃, such as the advanced products in firing ordinary refractory kiln plant in Shanghai possible.


Through active lime kiln back to actual production, research and development of magnesia aluminate spinel unfired brick. Use show, developed spinel unburned brick in the active lime kiln firing service life of more than one year. For a long time, directly from the dry combination of MGO brick manufacturers with excellent slag resistance and corrosion resistance, it is used in large alkaline rotary kiln Pu left. Currently the most widely used range of the steel industry, most of the largest refractory Mg - Al system is unshaped refractory, accounting for about 85% of the unshaped refractories of total production, it is widely used in the converter, ladle, iron package, furnace and blast, virtually all metallurgical thermal equipment.


Spinel has a high melting point, small thermal expansion, low thermal stress, thermal vibration stability, and it has a more stable chemical properties of alkaline slag has a strong resistance, aluminum-magnesia do not burn brick core point to be used, is one of the key substances to improve life. Due to the gradual maturity in recent years, synthetic spinel technology, the use of synthetic spinel materials directly produce good ladle brick as possible, so that it can significantly improve the properties.


Quality spinel is one of the key issues related to the inter-spinel bricks can achieve the proper effect. By introducing the screening laboratory tests and related information, the magnesia-rich spinel 20% to 30% of its corrosion resistance, structural spalling resistance and thermal shock properties are better. But ladle conditions are more factors in the production operation, the amount of added spinel requirements should be 30% to 40% is more reasonable. Therefore, in brick-making process, in addition to producing a good artificial spinel added, we must also note the addition of fused magnesia powder and alumina powder, so that the secondary spinel regenerated during use. Thereby improving bricks tomb of quality performance parts for the control of harmful impurities in particular low-melting material was Na20 and K2O content, the choice of raw materials need special attention exhausted.


Spinel (also known as spinel) has the formula MgO-Al2O3, containing Mg0 was 28.3%, Al2O3 71.7%. Spinel is only Mg0-Al2O3 binary system phase diagram of an intermediate compound, melting at 2 135 C.

2016年7月5日星期二

New Types of Refractory For The Glass Furnace

Low Cement Castable
Low cement castable can be widely used for those industrial furnace's working lining, permanent lining( working temperature under 1400c), such as little refining Ladle cover, Ladle & Tundish permanent layer, heating furnace working wall, top and bottom. Blast furnace body, Hot metal ladle permanent layer.
Fused cast AZS block has been successfully used in the crown for many years. It can be used at 1600℃ or 1650℃ and can withstand the cycle of cooling and heating well. Compared to fused cast AZS, fused cast alumina block refractories can be used at 1700℃ and has better mechanical strength and thermal stability.

In the past, high chromium brick was mainly used for the production of reinforced glass and sometimes in the insulation castable refractory material glass furnace. Now it is increasingly used in some soda-lime glass furnaces. It has much better corrosion resistance to glass and can prolong the service life of throat. Besides the throat, it is also used in the end wall, the angle brick of the feeder port. However, clay insulating bricks the chromium may color the glass liquid, thus it can not be used in the white glass furnace. It was primarily used in the colored glass furnace, but now it has been successfully used in the transparent container glass furnace.

Low glass phase fused cast AZS block has been successfully used in the superstructure. The development of the oxygen-fuel combustion technology makes it find wider application in the superstructure. Since it contains a low amount of glass phase, it has better creep refractory fiber board resistance and the amount of exuded glass phase has been reduced to a very low level.
Fused cast high zirconia block is a new type of refractory, mainly used in the glass contact areas in high quality glass furnace. It has a low potential of causing stones, knots and bubbles and can effectively reduce glass defects. It is also in some low alkali glass or hard borosilicate glass furnaces.

The need of the glass manufacturers to maintain and improve the quality of glass and expand the service life of the glass furnace and the impact and influence of the oxygen-fuel combustion technology, promote the improvement of refractories and development of the new insulating castable refractories.
Fused cast alumina block has been widely used in the crown of the oxygen-fuel furnace, especially when manufacturing high quality glass. Before the application of the oxygen-fuel combustion technology, only β alumina block is used in the superstructure of the melting furnace. Now both β fused cast alumina block and α-β fused cast alumina block can be used in the crown of the oxygen-fuel furnace for producing TV glass, float glass and borosilicate glass.

Henan Xinmi Changxing Refractory Material Co., Ltd. Located in Henan Province,China.ChangXing's product portfolio covers shaped products such as refractory materials,refractory brick, refractory castable,refractory nozzle, ceramic fiber, slide gate, etc; unshaped products including repair, construction and casting mixes and mortars.exported to more than 20 countries, such as Thailand, Indonesia, Pakistan, Saudi Arabia, South Africa, Turkey, Iran, Iraq and so on.

product list:
http://www.yilongrefractory.com/AllProductServlet?id=2&number=20

Suggestions On The Proper Use Of Fused Cast AZS

Chrome Corundum Abrasion Resistance Prefabricated Part for Heating Furnace
The products are produced by corundum and chromium oxide as main materials, formed from casting, after being treated under high temperature, it has high hot strength and good wear resistance, suitable for making the slide rail part of heating furnace.
For structures constructed with fused cast AZS and silica brick (such as the front wall of the feeder pool),each material should have its own structure, because they have different volume changes at high temperature. For the superstructure that is less than 8m, there is no need to leave expansion joints. For the superstructure ceramic fiber felt that is longer than 8m, it is recommended to divide it into several parts by expansion joints(4-6mm).
There are masonry joints between the sidewall block and the bottom block. When the refractory materials are heated, 4-5mm volume expansion per meter will be expanded into the masonry joints.
Fused cast AZS block has a higher thermal conductivity. When used in the sidewall, it parts near the liquid ladle castable level require bigger cooling air flow.

Based on the campaign life of the glass furnace, the indicators of the furnace operation and the physical and chemical properties and performance of fused cast AZS block, some reasonable suggestions high insulating brick are made on the proper use of the fused cast AZS.
Fused cast AZS is characterized with stable and dense structure and good corrosion resistance to glass. During 900-1200℃, it will have a abnormal volume expansion due to its crystal phase transition.

Henan Xinmi Changxing Refractory Material Co., Ltd. Located in Henan Province,China.ChangXing's product portfolio covers shaped products such as refractory materials,refractories brick, refractory castable,refractory nozzle, ceramic fiber, slide gate, etc; unshaped products including repair, construction and casting mixes and mortars.exported to more than 20 countries, such as Thailand, Indonesia, Pakistan, Saudi Arabia, South Africa, Turkey, Iran, Iraq and so on.

product list:
http://www.yilongrefractory.com/AllProductServlet?id=4&number=20

2016年6月26日星期日

What is Spun Ceramic Fiber Blanket

Ceramic Fiber Blanket
Ceramic Fiber Blanket
Spun ceramic fiber blanket has low thermal conductivity, low thermal capacity, excellent thermal stability and thermal shock resistance, excellent tensile strength, excellent thermal insulation, good fire protection and sound absorption. It can be used in industrial furnaces, heating devices,high temperature pipe lining, industrial high-temperature reaction equipment, heating equipment lining, power boilers, gas turbine, furnace door, and high-temperature filter materials.

The heat capacity of spun ceramic fiber blanket is only 1/10 of that of lightweight refractories lining and light castable refractory material lining. The heat capacity of the lining material is is proportional to its weight. Low heat capacity means less heat absorption of the furnace in the reciprocating operation and higher heating rate. It can greatly reduce energy consumption of the temperature operation control, refractory company especially the start and shutedown of the heating furnace.

Spun ceramic fiber blanket is made of spun ceramic fiber cotton by needling, heat setting, vertically and horizontally cutting and rolling. Ceramic fiber blankets with different thickness and density provide a wide range of choice of materials to obtain the best insulation and energy efficiency.
Spun ceramic fiber blanket has uniform diameter, long fiber and low content of slag balls. Its interleaving degree, delamination, properties, erosion ressitance, flexibility and tensile strength are all improved, which improves the application performance of spun blanket and reduces the material loss. Spun blanket does not contain any binding agent to ensure that products have good reliability and stability in various environments.

Henan Xinmi Changxing Refractory Material Co., Ltd. Located in Henan Province,China.ChangXing's product portfolio covers shaped products such as refractory materials,refractory brick , refractory castable,refractory nozzle, ceramic fiber, slide gate, etc; unshaped products including repair, construction and casting mixes and mortars.exported to more than 20 countries, such as Thailand, Indonesia, Pakistan, Saudi Arabia, South Africa, Turkey, Iran, Iraq and so on.

http://www.yilongrefractory.com/AllProductServlet?id=1&number=20

2016年6月23日星期四

Bonded Again Fused Cast Alumina Block

Clay, Aluminum Refractory Mortar
Bonded again fused cast alumina block is a type of bonded again sintered refractories brick made of fused corundum clinker as the granular material and fused corundum or sintered

corundum powder as the matrix.

The batching of granular materials should be according to the principles of tightly packing, multilevel ratio, refractory company less intermediate particles and more fine powder. This can improve

the density and sintering of the products. The additives include aluminum phosphate, phosphoric acid, aluminum chromium phosphate, cellulose and pulp waste solution. Among them,

he most promising is active phosphate. Recently, ammonium phosphate is on the trial and achieves good magnesia carbon brick results. The mud should be mixed evenly with a moisture content of 3-4%.

After high pressure molding, high dense bricks are obtained.

There are a few harmful ingredients in the corundum which will cause poor sintering or cracking, firebrick refractory sale so corundum should be pre-calcined before use. The residual ferro-silicon alloy

is oxidized and decomposed into Fe2O3 and SiO2 at 500-1000℃ and Ti in the minerals can be oxidized into TiO2 (rutile), which can cause large volume expansion. After pre-

calcining, the stress caused by those decomposition reactions and oxidation reactions can be eliminated during the pre-calcining process and cracks caused by the volume

expansion of those impurities can be avoided during the sintering process.
Fused corundum block has large volume, so it should be smashed with drop hammers and other ways and then high insulating brick pulverized. The pulverized fused corundum is stored by size after

screened. Fused corundum is hard and difficult to grind. Therefore it is wet ground by ball mills or vibration ball mills. The grain size can be less than 40μm or even 10μm.

The iron in the granular material can be removed with electromagnets and the iron in the fine powder can be washed with acids.


When using fused brown corundum or white corundum as raw materials, the frits should be smashed and then processed by removing the ferro-silicon alloy and other impurities.

White corundum should be processed by removing the flaky sodium aluminate crystals and other low-melting substances. The impurities are easy to be identified since they have low

density and float in the surface of corundum frits.

The fused cast alumina block has high purity. It is difficult to sintere and should be sintered at 1800℃. The type of the kilns used depends on the production scale. For small

batch production, high-temperature batch kiln is better. For batch stable production, the small high-temperature tunnel kiln is used.

Henan Xinmi Changxing Refractory Material Co., Ltd. Located in Henan Province,China.ChangXing's product portfolio covers shaped products such as refractory materials,refractory

brick, refractory castable,refractory nozzle, ceramic fiber, slide gate, etc; unshaped products including repair, construction and casting mixes and mortars.exported to more

than 20 countries, such as Thailand, Indonesia, Pakistan, Saudi Arabia, South Africa, Turkey, Iran, Iraq and so on.

2016年6月5日星期日

Chemical composition of fire clay bricks

Clay, High Alumina Insulating Bricks
The use of the bricks can reduce the heat capacity of kiln walls and promote the heat efficiency of kilns. The product is applicable for constructing industrial kilns and inner lining of kilns.
Fire clay brick is the refractory brick containing 30-46% SiO2. It is made of clinkers calcined from refractory clays as the oxidant and bond clay as a binder agent.
The main raw material is firebrick refractory clay. Clay is an earthy mineral. It can form plastic mud pie when mixed with water and maintain the shape after drying. It has rock-like hardness after fired at high temperature.
Additionally, the clay contains a certain amount of impurities such as quartz, mica, pyrite, feldspar and organic substances. The impurities, especially iron, can reduce the quality of clay refractory brick for sale and are harmful to the fire clay bricks.
Alkalis such as Na2O and K2O exist as mica. It can improve the sintering properties of clay and form dense products after sintered. It should be fewer than 2%.
The content of CaO is generally ladle refractory under 11.5% and distributed evenly. So, it will not affect the refractory properties of raw materials.
There is a certain amount of TiO2 in the bond clay. It exists as diamond. When it is less than 1%, it has no big effect on the quality of bond clay. In the chemical analysis, its content is not tested alone but counted in the content of A1203 + TiO2.
When the impurities in the clay exceed 6%, the refractories of clay will decease and cannot be used as the raw materials. The content of organic substances in the clay is fluctuated greatly, up to 5%.

refractory company Henan Xinmi Changxing Refractory Material Co., Ltd. Located in Henan Province,China.ChangXing's product portfolio covers shaped products such as refractory materials,refractory brick, refractory castable,refractory nozzle, ceramic fiber, slide gate, etc; unshaped products including repair, construction and casting mixes and mortars.exported to more than 20 countries, such as Thailand, Indonesia, Pakistan, Saudi Arabia, South Africa, Turkey, Iran, Iraq and so on.

Nest article:

Application of monolithic refractories on industrial furnaces

2016年6月1日星期三

Refractories for cement industry

Calcium Silicate Pipe
calcium silicate product is used in industries including steel plants, cement clinker kiln, heat and power stations, foundries both ferrous and non-ferrous, cement producers, Aleris , ceramics, coke plants, incinerators, renewable energy, chemical works, sugar refineries and petrochemical industry. It is sell well in the world and we won a lot of trust both at home and abroad .
Alkaline Refractories
Alkaline refractory material is available for high temperature calcination, also has superior chemical resistance property, which is a main refractory material for cement kiln to keep high production quality, high yield, low consumption and long-term safe operation. Currently main material for cement kilns include direct-bonded magnesia chrome brick, semi-direct bonded magnesia chrome brick, ordinary magnesia chrome brick , dolomite brick, zirconium and zirconium-free special magnesite brick, spinel brick and chemically bonded unburned magnesia chrome brick.
Bricks properties are listed as follows:

High alumina brickHigh alumina brick has high compressive high insulating brick strength, high refractoriness under load and good thermal shock resistance. Because of its low cost with high quality, it is widely used in varieties of cement kilns. When to be used in arch crown, calcined alumina brick is better. High alumina bricks suitable for cement kilns include phosphate bonded alumina brick, phosphate bonded high alumina wear-resistant brick, anti-stripping alumina brick, chemically bound (special) castable refractory material alumina brick and general alumina brick and so on.
Alkali Brick Series
Alkali brick has excellent alkali corrosion performance, under certain conditions, it will react with the alkali compound kiln materials and kiln gas, rapidl. yclay insulating bricks forming enclosed type dense protective enamel layer on the turn, preventing the continuing internal mixing and bricks "base crack ", which is a indispensable kiln lining material in NSP kiln. This series bricks include ordinary alkali-resistant brick, high-strength alkali-resistant brick, insulation alkali-resistant brick and arch type alkali-resistant brick.
Series refractory castables
Refractory castables can be produced with simple production process, which is flexible and convenient to be used in the cement kiln system. It has become increasingly common to be applied in the complex structure of cement kiln preheater system. Refractory castables suitable for cement kiln mainly include corundum castable, high alumina castable, alkali-resistant castables and light weight castable.

article source:
nest article:

2016年4月24日星期日

Magnesia Alumina Carbon Brick, Alumina Magnesia Carbon Brick

Magnesia Alumina Carbon Brick, Alumina Magnesia Carbon Brick

Introduction

Alumina Magnesia Carbon Bricks is made from high quality bauxite, corundum and fused magnesia. It is formulated with very high purity alumina and magnesia.

Advantages

It has low thermal conductivity, good isolation ability, and appropriate residual expansion

Application

Alumina Magnesia Carbon Bricks are used in Ladle Sidewall and Bottom impact areas.
End of magnesia bricks mainly used in steel-making silica mortar, electric furnace and the furnace walls, permanent oxygen converter lining, non-ferrous metal smelting furnaces, high temperature tunnel kilns, calcined magnesia brick and cement kiln liner, bottom of heating furnace and the furnace walls, glass furnace regenerator checkers.

Our company magnesia brick by sinter magnesite as raw material, the reasonable gradation, high pressure forming, high temperature sintering. This product is relatively slag corrosion resistance.


http://www.yilongrefractory.com/ProductServletOne?id1=1&id=4

2016年4月20日星期三

Introduction and advantages of Chromite Sand

Chromite ore is also called chromite sand which is a kind of special sand for casting. Some natural spinel based mainly on chromite ore, then be crushed, grinded and filtered, thus filter the specified size chromite sand out which can be used as modeling sand.
The main content of chromite sand is Cr2O3. It is characterized with stable heating area, ......